Key points
- A building still standing after a fire is not automatically safe; clear affected areas and call a structural engineer.
- Concrete colour hints at the temperature reached, but concrete that has not changed colour may still be damaged.
- The assessment combines visual inspection, rebound hammer tests, cores and an analysis of each member's remaining capacity.
- The results decide which members can be repaired, need strengthening or must be replaced.
A structural assessment after fire is needed before a building is used again, even when it still looks solid. High temperatures can reduce the strength of concrete and reinforcement without leaving obvious marks on the surface. This article explains the steps engineers usually follow, from making the site safe to recommending repairs.
Safety first
Once the fire is out, the first priority is people's safety, not listing the damage. Members that sag, show wide cracks or have lost their concrete cover can fail at any moment, and spalled concrete can fall without warning.
- Clear the burnt area and the floor below, and put up barriers.
- Do not move heavy goods onto affected floors or add load above them.
- If you see clear deflection, large cracks or hear unusual sounds, keep people away and call a structural engineer immediately.
- Install temporary propping (shoring) only as directed by an engineer, because badly placed props can shift load onto weakened members.
Tip: Record the condition with photos and video as soon as possible, before debris is cleared. Soot patterns, concrete colour and melted objects help the engineer estimate how the heat spread.
Steps in a structural assessment after fire
A post-fire assessment usually moves from quick checks to detailed ones:
- Collect information: structural drawings (if available), room use, how long and where the fire burned, and how it was extinguished.
- Visual inspection: map affected members and record cracks, spalling, exposed bars, deflection and colour changes.
- Site testing: sounding, rebound hammer tests and concrete cores from burnt areas and from unaffected reference areas.
- Laboratory testing: core compressive strength and, where needed, petrographic examination to see how deep the damage goes.
- Capacity analysis: recalculating each member's load capacity using the tested material properties.
- Recommendations: which members need surface repair, which need strengthening and which must be replaced.
Dividing the building into damage zones during the visual inspection decides where tests are taken, so the number of samples stays reasonable.
Reading the signs in concrete
Concrete colour gives a first clue to the temperature it reached. The VicRoads technical note on fire-damaged concrete states that concrete turning pink indicates it reached about 300°C, a temperature already linked to a significant loss of strength. Above about 600°C, concrete turns greyish, friable and porous.
Colour is not the final answer, though. The same note stresses that concrete which has not turned pink is not necessarily undamaged, so visual inspection is always backed by testing.
Other signs to record:
- Spalling: surface layers breaking off, sometimes suddenly because of steam in the pores, or when hot concrete is hit by firefighting water.
- Cracking: fine map cracking over the surface, or cracks following the bars.
- Sound when tapped: sound concrete rings clearly, while damaged concrete tends to sound dull.
- Deflection and movement: sagging beams or slabs and leaning walls point to more serious problems.
What happens to the reinforcement
Bars inside concrete are protected by the cover, but only up to a point. According to the VicRoads note, hot-rolled reinforcement generally recovers its strength on cooling if it stayed below about 600°C; above that, the loss is permanent. Bond between concrete and steel can also deteriorate once the surrounding concrete passes about 300°C.
Prestressing steel is more sensitive to heat, so buildings with post-tensioned slabs or prestressed beams need particular care. In steel structures, look for buckled sections, distorted connections and damaged fire protection.
Material testing and capacity analysis
Site testing usually compares burnt areas with protected areas of the same building:
| Method | Purpose |
|---|---|
| Rebound hammer | Quickly compares surface hardness between areas |
| Core drilling | Measures actual concrete compressive strength |
| Petrography | Shows how deep the damaged zone goes |
| Reinforcement checks | Inspects exposed bars or samples taken from them |
Rebound hammer results alone cannot confirm concrete strength; they need to be related to core results. Both tests are explained in our article on hammer tests and core drilling.
The test data then feed a structural analysis of each key member's remaining capacity. This must be done by a competent engineer, because every building has its own structural system, loads and fire history.
Repair options
The final recommendations usually group members as follows:
- Surface repair: damaged concrete is broken out to sound material, bars are cleaned, and the profile is rebuilt with repair mortar or sprayed concrete.
- Strengthening: where remaining capacity is no longer enough, for example with jacketing, CFRP or added steel members.
- Replacement: badly damaged or permanently deformed members are removed and rebuilt.
After repair, the building must be confirmed fit for use again. This links to the SLF renewal process, and cracks that appear later can be judged with our guide to hairline vs structural cracks.
Conclusion
A building that is still standing after a fire is not automatically safe to use. A structural assessment after fire combines visual inspection, material testing and capacity analysis to decide which members can be repaired, strengthened or replaced. If your building has recently had a fire, talk to us through our structural audit and assessment service.
This article provides general information. Every project still needs to be analysed and calculated by a competent structural or geotechnical engineer, in line with the applicable SNI codes and regulations.

